The Tree: The tree is a piece of Manzanita with bark added from putty. The foliage is made from the small dried flowers from the craft store. There are about six areas where I added even finer looking branches from another variety of dried flower to fill in some spots and make the tree more interesting. The whole assembled tree was airbrushed with a brown/grey color and then the leaves were airbrushed with a medium green. The branches that were inevitably coated in some green, were then washed with the cel paint by hand to get the color back to the brown/grey. This takes a little time but the thinned paint will cover fairly easily any place you can reach. The leaves were then highlighted with a few shades of green and orange spotted around to keep your eye moving. The process took some time but it wasn’t overwhelming. Assembly of the Components: A hole was drilled in the middle of the tree surround and another up into the base of the tree. A small eyehook was then screwed into the tree through the hole in the base. This allows the tree to actually rotate and be pinched tight to the base without the need for glue. The fence was placed by drilling small holes and gluing the posts in the holes. The well was glued directly to the base. The tank was positioned by drilling holes in two places of the hull and the base and bolting it to the base. The opening for the smoke was drilled out of the hull and the base and a piece of plastic tube was inserted to create a smokestack of sorts. The Smoke: The smoke effect was accomplished by using a smoke unit for model railroads.The unit I purchased is made by SEUTHE-SCHLEY GMBH. I don’t know anything about these units but this one seemed to be very compact and very adaptable. This is the area I alluded to that I have no experience in and the task of getting the smoke to work was intimidating. In order to make use of this unit, you need to be able to solder a little and know/learn a little something about electricity and making a circuit. In my case, I had help from a friend to get me set up to create the electrical circuit. I think someone being helpful at the electronics store will also work and after the cost of the smoke unit, the rest of the components are very inexpensive. I constructed a base from poplar scraps that would conform to my cobblestone perimeter and also be deep enough to enclose the smoke unit and batteries. I purchased two battery holders for 9-volt batteries, two battery cap terminals and a toggle switch. The smoke unit is captured in a plastic film canister by drilling a couple of small holes in the side and passing the wires through, letting the device hang in the middle of the canister. The film canister was set in the middle of an upturned aerosol paint can lid. This was bolted to the bottom of the base box. This worked out well because it gave a solid base to keep the smoke fluid and another reservoir in case of spilling when being moved. NOTE: This setup of the film canister and aerosol can lid is also good for holding custom mixes of paints if the lid is screwed to a board on your tabletop. It’s very hard to spill the paint and you can use the reservoir for water or thinner if you are doing washes, as an example. The “circuit” was created as shown in the photo and the wires just needed to be twisted together and soldered to make sure. The toggle was mounted in the side of the base after drilling a hole and pressing it tightly in. The smoke unit instructions show how the circuit is connected in order for the smoke to happen. The best effect is obtained using a power source of 16 volts but I was able to get some smoke with one 9-volt battery. It was simple (for me) to add another battery and 18 volts is close enough to get a good plume of smoke. Trying to reproduce this, larger or smaller batteries could be used through some experimenting. The smoke unit works by heating the special oil and creating steam. Everyone I asked told me I couldn’t color it to make it darker but I did find out you can buy it with different scents if that helps anybody. The steam rises and actually gives the surfaces of the tank a slight sheen as it settles. This makes it look light a light rain has fallen, so it’s not terrible. I did notice that the sheen seems to evaporate eventually so it really is not a problem. Go to page 4

Page 1 | Page 2 | Page 3 | Page 4