The Tank Construction: I spent some time researching the tank I wanted to model and I decided I liked the look of the longer barreled H39. Color reference came from a book loaded with color plates of all kinds of WWII tanks, of all countries. The technical reference was harder for me to digest, as I was able to find some information via the web and in two publications on the 1940 campaign. All of it was in French though and that’s a bit of a struggle for me. Through this phase, I became aware the Heller kit wasn’t perfect and I tried to make a couple of changes that were easy enough to tackle. For the most part, I left the kit as is and really wanted to concentrate on the overall concept of the burning vehicle. The French armor experts will have to forgive me but I was impatient to see the project through. I left all the tools off the tank and indicated their clamps with metal strips. I rebuilt the jack and crank and placed them on the ground. Most of the reference photos I have of knocked out or abandoned tanks, show the tools have been scavenged and I thought this made sense considering the setting I was creating. I was able to “tame” the flexible kit tracks by pinching them to the top of the return rollers with wire coming out from the hull sides. The length in front of the tank was wired to the ground by drilling two small holes in the base and tying it down with wire. Painting The Tank: The tank was airbrushed with an overall coat of a tan that really leaned more towards a peach color instead of yellow. I then drew the outlines of the camouflage areas with a brown colored pencil and hand painted the olive/med green areas. I then hand painted the chocolate brown outlines with a fine lettering brush and went back and forth with the base peach and green to clean up the lines and make the width consistent. I hand painted the roundels by using the pencil and a circle template for the outline and just “eyeballing” the colors until they looked consistent. The turret numbers were hand painted using a sort of a stencil. I have some text “stickers” from the craft store that can be peeled and arranged to personalize craft projects. The sticky “negative” part of the sheet was used to make the mask and the number “2” was painted in white with a brush. The tank was given some weathering of burnt umber to age the colors and some pastel powder mixed with alcohol. Graphite was added to some edges and all across the tracks. Black pastel was rubbed onto the engine deck to indicate scorching. The tank was painted after assembly, right on the base. The base and well were also painted with the tank already in place. This wasn’t too difficult as the base is a lot of earthy, non-exact colors. The tree and fence were painted separately and touched up after attaching to the base. A note about painting: I primarily use acrylic paints that are marketed to cartoon animators, as well as all the brands of ceramic paints for painting plaster casts. I have very few true model brand paints and I guess I’m settled into a process that works for me. I like the animators (or cel paints) because they dry flat and cover extremely well, light over dark as in the case of the roundels and turret numbers. The other example is the ease with which I could paint back the camouflage colors to narrow the brown outlines. They airbrush easily after thinning and because they are formulated to stick to clear acetate sheets, you can even get by with painting resin and plastic with no primer if you want. The range of colors is extensive and I consider them an economical alternative when comparing the amount of color per bottle to model paints. The ceramic paints are great for washes and staining, again for their economy and vast color range. The Base: The base for the vignette is MPD-011 Cobblestone Corner. It measures approximately 8” x 8” and it allows for a comfortable fit of the French tank. It was primed with VHT Aerosol grey primer and various colors of ceramic paints were applied to get the weathered cobblestone look to the street sections. Some finely ground foam was applied in the grass areas with a wash of thinned white glue to act as the adhesive. The tree surround was painted a dark rust color and highlighted with graphite. The well is MPD-010 and it was painted in the same manner as the base. Just mix a warm grey color that looks “right” and weather the surfaces with some darker washes and some green algae stain. The fence railing is lasercut card with small metal balls added on top. The fence is an experiment and not yet for sale. It was painted a dark green and then washed with a little lighter shade to make it look a little more substantial. Go to page 3

Page 1 | Page2 | Page3 | Page4